DRAIN STR/ORIFICE

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

NAVSUP WEAPON SYSTEMS SUPPORT MECH

Contract Value

Not provided

Codes & Classification
Solicitation Number

N0010426QFF70

NAICS

332913 - Plumbing Fixture Fitting and Trim Manufacturing

Classification Code

4510

Additional Details
Set Aside

None

Place of Performance

-

SourceSAM
The Department of the Navy, through the Naval Supply Systems Command (NAVSUP) Weapon Systems Support office in Mechanicsburg, PA, has issued a solicitation (Procurement Identifier: N0010426QFF70) for the manufacture and supply of a critical shipboard component: the 1 Inch, 900 PSI Steam Socketweld Drain Strainer/Orifice. This procurement is classified under NAICS code 332913 (Plumbing Fixture Fitting and Trim Manufacturing) and Product Service Code 4510 (Plumbing Fixtures and Accessories), and is a Total Small Business Set-Aside, inviting participation exclusively from qualified small business concerns. **Purpose and Scope** The primary objective of this procurement is to acquire Drain Strainer/Orifice assemblies that are integral to crucial shipboard systems. These components are designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured) due to their criticality; failure or nonconformance could result in severe personnel injury, loss of life, or catastrophic shipboard system failure. As such, the contract invokes stringent quality assurance, traceability, and certification requirements to ensure the highest standards of safety and reliability. **Key Requirements and Deliverables** Contractors are required to manufacture the complete assembly in strict accordance with Naval Sea Systems Command Drawing 803-5001057, Assembly 803-5001057-S3AF-375, with specific modifications detailed in the solicitation. Notably, the orifice plate must feature a 0.375 ± 0.001 inch thru-hole, superseding the chamfered/counterbore dimensions shown in the illustration. Material and process requirements are highly prescriptive: - **Materials:** Key parts such as the body and cap must be fabricated from ASTM-A182, Grade F316 stainless steel; studs and nuts must conform to MIL-DTL-1222, with specified grades and coatings (phosphate or zinc plating per ASTM-B633 or MIL-DTL-16232). - **Testing and Certification:** Comprehensive certifications are required for chemical and mechanical properties, non-destructive testing (NDT), hydrostatic testing, and hydrogen embrittlement relief (for plated/coated fasteners). All certifications must reference applicable standards and be traceable to individual items via unique markings. - **Welding and Brazing:** All welding and brazing must comply with NAVSEA and MIL standards, with procedures and personnel qualifications submitted for approval prior to production. Consumed weld metal must be certified, and all welding records maintained. - **Quality System:** Contractors must maintain a quality system compliant with ISO 9001 (or MIL-I-45208 as an alternate), with calibration systems per ISO 10012 or ANSI-Z540.3/ISO-17025. The system is subject to government audit and approval. - **Traceability:** Full traceability from raw material to finished product is mandatory, with permanent marking per MIL-STD-792 and MIL-DTL-1222 for fasteners. Certification data must be submitted and accepted prior to shipment. - **Packaging:** Preservation, packaging, and marking must comply with MIL-STD-2073 and contract-specific instructions. **Contract Administration and Compliance** The contract requires submission of all certification and test documentation to Portsmouth Naval Shipyard for review and acceptance prior to each shipment, using the Wide Area Work Flow (WAWF) system. No material may be shipped without formal acceptance. The government reserves the right to perform source inspection at the contractor’s or subcontractor’s facility, and all waivers or deviations from contract requirements must be formally requested and approved. **Special Considerations** - **Critical Safety Item (CSI):** The item is classified as a CSI, meaning any failure could have catastrophic consequences. This drives the heightened emphasis on quality, traceability, and configuration control. - **Configuration Control:** Contractors must maintain the equipment baseline and submit Engineering Change Proposals (ECPs) for any modifications affecting form, fit, function, or interface. - **Mercury-Free Requirement:** No mercury or mercury-containing compounds may be used or come into contact with the supplied hardware. - **Electronic Signatures:** Certification documents may use electronic signatures, provided they are controlled and uniquely attributable to the signer. **Contracting Entity and Contact Information** - **Contracting Office:** NAVSUP Weapon Systems Support (NAVSUP-WSS), Mechanicsburg, PA - **Department/Agency:** Department of Defense, Department of the Navy - **Primary Contact:** Christian M. Valdez, Telephone: 717-605-3229, Email: [email protected] **Procurement Details** - **Solicitation Type:** Fixed-price supply contract - **Set-Aside:** Total Small Business Set-Aside - **FOB:** Destination - **Warranty:** One year from date of delivery - **Response Deadline:** October 30, 2026, 20:10 - **Notice Status:** Active - **Notice URL:** [https://sam.gov/opp/69781aaa657b4d83853b69609961cfa0/view](https://sam.gov/opp/69781aaa657b4d83853b69609961cfa0) **Summary for Contractors** This opportunity is best suited for small businesses with demonstrated expertise in precision manufacturing for the defense sector, robust quality assurance systems, and the ability to comply with rigorous Navy technical and certification requirements. Contractors must be prepared for extensive documentation, traceability, and government oversight throughout the contract lifecycle. The technical and administrative requirements outlined in this solicitation are expected to remain constant for the duration of the contract, reflecting the enduring criticality and safety implications of the supplied material.