Paddle blender/ribbon blender for the USDA, ARS in Fort Pierce, FL

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

USDA ARS AFM APD

Contract Value

Not provided

Codes & Classification
Solicitation Number

1232SA26FF0068339

NAICS

333241 - Food Product Machinery Manufacturing

Classification Code

3605

Additional Details
Set Aside

SBA

Place of Performance

Fort Pierce, Florida, UNITED STATES

SourceSAM
The United States Department of Agriculture (USDA), Agricultural Research Service (ARS), Acquisition and Property Division (APD) is conducting a sources sought market research to identify qualified manufacturers or contractors capable of supplying a domestically sourced paddle blender/ribbon blender. This equipment is intended for use at the U.S. Horticultural Research Laboratory, located within the Harbor Branch Oceanographic Institute in Fort Pierce, Florida. The primary objective is to determine the availability of domestic sources that can meet the specified requirements, supporting the agency’s ongoing research activities related to the mixing of wet and dry ingredients for extruding fish feeds. This notice, posted in accordance with FAR Part 5.2, is not a solicitation or request for proposal, and no contract award will result from responses. Instead, the information gathered will inform the government’s acquisition strategy, including whether to proceed with an unrestricted solicitation and full and open competition. The anticipated solicitation release date is July 31, 2026, with delivery of the equipment expected within ninety days after award. The paddle blender/ribbon blender must meet or exceed the following minimum specifications: - Capacity: Minimum of 50 gallons - Bulk density rating: Minimum of 55 pounds per cubic foot - Agitator speed: Minimum 50 rotations per minute at 60 hertz (Hz) - Trough size: Maximum 20 inches in width and 40 inches in length - Overall dimensions: Maximum 75 inches in width and 40 inches in length - Motor: 3 horsepower, 60 Hz, 230/460 volt, 3-phase - Wetted parts, interior and exterior finish: Stainless steel type 304 - Shaft design: Stainless steel type 304 with OSHA-compliant safety guards - Cover gasket: FDA-compliant to reduce dust - Support design: OSHA-compliant carbon steel painted shaft guards - Discharge valve: Manually operated stainless steel type 304, dust-tight knife gate valve with minimum diameter of 4 inches, FDA-compliant urethane seal and silicone O-ring - Keypad: Includes start/stop control, speed control and display, scrolling display for amps, percentage of load, and other digital values The procurement is classified under NAICS Code 333241 (Food Product Machinery Manufacturing), with Product Service Code 3605. The set-aside type is SBA, and interested parties are encouraged to indicate their business status (Small Business, SBA-certified HUBZone, SBA-certified 8(a), Service-Disabled Veteran-Owned Small Business, or Women-Owned Small Business) as well as the country of origin for the proposed equipment and accessories. Potential respondents must be registered in the System for Award Management (SAM) prior to submitting a capabilities statement. All future solicitations and updates will be posted exclusively on SAM.gov, and interested parties are responsible for monitoring the site. No proposals, bids, or quotes should be submitted at this time, and the government will not pay for any information provided in response to this notice. Interested companies with relevant experience and capabilities are invited to submit a brief capabilities statement by July 24, 2026, no later than 3:00 p.m. EDT. Submissions should be directed to Shelley C. Steen at [email protected]. For further information, Shelley Steen can also be reached at 510-559-6350. This opportunity is managed by the USDA ARS AFM APD, a federal office within the Department of Agriculture’s Agricultural Research Service. The place of performance is Fort Pierce, Florida, United States. Contractors evaluating this opportunity should ensure their ability to provide a domestically sourced paddle blender/ribbon blender that meets the detailed technical requirements and delivery expectations, and be prepared to demonstrate their qualifications and compliance with federal procurement standards. For additional details and updates, refer to the official notice on SAM.gov: https://sam.gov/opp/270d3a12dcfa476d90c972e7fdda727b/view.