STEM,FLUID VALVE
Key Dates
Due Date
-
Posted Date
-
Agency & Value
Agency
NAVSUP WEAPON SYSTEMS SUPPORT MECH
Contract Value
Not provided
Codes & Classification
Solicitation Number
N0010426QZB36
NAICS
332919 - Other Metal Valve and Pipe Fitting Manufacturing
Classification Code
4820
Additional Details
The Department of the Navy, through NAVSUP Weapon Systems Support (NAVSUP WSS) Mechanicsburg, has issued a solicitation (Procurement Identifier: N0010426QZB36) for the procurement of a STEM component for a fluid valve, specifically a stem for a 4-inch ball valve. This procurement is classified under NAICS code 332919 (Other Metal Valve and Pipe Fitting Manufacturing) and Product Service Code 4820, indicating its focus on specialized shipboard valve components. The solicitation is a total small business set-aside, providing an opportunity exclusively for qualified small business contractors.
**Purpose and Scope**
The primary objective of this procurement is to acquire a critical valve stem component intended for use in a crucial shipboard system. The nature of this requirement is such that the use of incorrect or defective material could result in catastrophic consequences, including serious personnel injury, loss of life, or loss of vital shipboard systems. As such, the material is designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured), invoking stringent control and certification procedures to ensure the highest level of quality and traceability.
**Key Requirements and Deliverables**
Contractors are required to manufacture the valve stem in accordance with Newport News Shipbuilding Drawing 255587, Piece 11, Figure 10, with specific modifications and amplifications as detailed in the solicitation. The stem must be fabricated from QQ-N-286, Form 2, annealed and age-hardened material, with no weld repairs permitted. All material must undergo quantitative chemical and mechanical analysis, and certifications are required for annealing, age hardening, and ultrasonic inspection of the starting material, particularly for items with a diameter or minimum distance between parallel surfaces of 4 inches or greater.
Testing for the slow strain rate tensile properties of QQ-N-286 must be performed by one of several specified laboratories, ensuring consistency and reliability in test results. O-ring grooves and mating sealing surfaces are subject to rigorous inspection criteria, and any repairs must remain within the dimensional limits specified in the applicable drawings.
Contractors must maintain configuration control and submit Engineering Change Proposals (ECPs) for any modifications affecting form, fit, function, or interface parameters. All waivers and deviations require prior approval from the Contracting Officer.
A comprehensive certificate of compliance is required, certifying that all items furnished meet the requirements of the procurement document and all invoked specifications and drawings. Mercury and mercury-containing compounds are strictly prohibited in the manufacturing process.
**Quality Assurance and Certification**
The contractor must implement and maintain a quality system compliant with ISO-9001 (or MIL-I-45208 as an alternate), with calibration systems meeting ISO-10012 or ANSI-Z540.3 with ISO-17025 standards. The quality system and all products are subject to government evaluation, verification, and acceptance. Government Quality Assurance (GQA) will be performed at the source, and any changes to the quality system require government concurrence.
Traceability is a critical aspect of this procurement. All material must be traceable from the raw stock through all processing steps to the finished component, with permanent markings in accordance with MIL-STD-792. Certification data must be submitted to Portsmouth Naval Shipyard for review and acceptance prior to each shipment, and no material may be shipped before acceptance is granted.
**Packaging and Delivery**
Preservation, packaging, packing, and marking must comply with MIL-STD-2073 and the contract schedule. Partial and early deliveries are authorized and encouraged, provided they are at no additional cost to the government.
**Contracting Entity and Contact Information**
- **Contracting Entity:** NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH)
- **Department:** Department of Defense, Department of the Navy
- **Primary Contact:** Michael E. Thoman, Telephone: 717-605-4608, Email: [email protected]
- **Notice URL:** [SAM.gov Opportunity](https://sam.gov/opp/9542c5df70ae4b929009348d0d57e617/view)
**Procurement Type and Special Considerations**
This is a fixed-price procurement, issued as a total small business set-aside. The solicitation is a rated order certified for national defense use under the Defense Priorities and Allocations System (DPAS), and contractors must comply with all related requirements. The procurement is subject to the Buy American Act, Free Trade Agreements, and Balance of Payments Program provisions.
All contractual documents and communications will be managed electronically, and the government’s acceptance of the contractor’s proposal constitutes bilateral agreement to issue contractual documents as detailed in the solicitation.
**Summary for Contractors**
This opportunity is best suited for small business manufacturers with demonstrated experience in producing high-reliability, traceable, and quality-assured metal valve components for critical shipboard applications. Contractors must have robust quality assurance systems, the ability to maintain strict material traceability, and the capacity to comply with detailed certification and inspection requirements. The procurement’s critical safety designation and national defense priority underscore the importance of compliance with all technical, quality, and delivery requirements throughout the contract lifecycle.
Interested contractors should review the full solicitation and associated technical documents, ensure they can meet all mandatory requirements, and prepare to submit all required certifications and documentation as specified. All questions and submissions should be directed to the primary contact listed above.