TUBING,NONMETALLIC

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

NAVSUP WEAPON SYSTEMS SUPPORT MECH

Contract Value

Not provided

Codes & Classification
Solicitation Number

N0010426QFE12

NAICS

326220 - Rubber and Plastics Hoses and Belting Manufacturing

Classification Code

4720

Additional Details
Set Aside

None

Place of Performance

-

SourceSAM
The Department of the Navy, through NAVSUP Weapon Systems Support (NAVSUP WSS) Mechanicsburg, has issued a solicitation (Procurement Identifier: N0010426QFE12) for the supply of nonmetallic tubing, specifically MC 903 Nylon Tube for Ball Valve Seat Seal material. This procurement is classified under NAICS Code 326220 (Rubber and Plastics Hoses and Belting Manufacturing) and Product Service Code 4720, indicating its relevance to contractors specializing in the manufacture of rubber and plastic hoses, belting, and related products. **Purpose and Scope** The tubing sought under this contract will be used in a critical shipboard system, where the integrity and reliability of the material are paramount. The use of incorrect or defective material could result in catastrophic failure, including serious personnel injury, loss of life, or loss of vital shipboard systems. As such, the material is designated as SPECIAL EMPHASIS (Level I, Scope of Certification, or Quality Assured), invoking stringent control procedures to ensure the receipt of correct and compliant material. **Key Requirements and Objectives** The contract specifies MC 903 Nylon Tube, produced via direct polymerization of polyepsilon caprolactam, conforming to Electric Boat Division Specification 2000 or equivalent. The required tube dimensions are: - Outside Diameter: 10.000 inches - Inside Diameter: 4.500 inches - Length: 13.000 inches Material properties must meet rigorous standards, including melting point, relative viscosity, specific gravity, dimensional change, tensile impact, tensile yield stress, compressive strength, water absorption, and Rockwell hardness, as detailed in the solicitation. All material must be mercury-free, and traceability from raw material to finished product is mandatory, with permanent marking requirements per MIL-STD-792. **Quality Assurance and Certification** Contractors must maintain a quality system compliant with ISO-9001, ISO-10012, ISO/IEC 17025, or MIL-I-45208, with calibration requirements per ANSI/NCSL Z540.3. The quality system and products are subject to government evaluation, verification, inspection, and acceptance. Suppliers of Level I/SUBSAFE material must submit documented quality system procedures to the Procurement Contracting Officer (PCO) prior to award, unless already on file. Objective Quality Evidence (OQE) is required for all mechanical, chemical, and performance tests, and certification data must be submitted to Portsmouth Naval Shipyard for review and acceptance prior to each shipment. No material may be shipped before acceptance is received. The certificate of compliance must show traceability to the marking applied on each item and include detailed information as outlined in the solicitation. **Configuration Control and Change Management** Contractors are responsible for maintaining the equipment baseline configuration and must submit Engineering Change Proposals (ECPs) for any modifications affecting form, fit, function, or interface parameters. All waivers and deviations require review and approval by the Contracting Officer and must be classified as critical, major, or minor. **Inspection and Acceptance** Government Quality Assurance will be performed at the source, and the place of performance may not be changed without authorization. The contractor must maintain records of all inspections and tests, and subcontractor inspection requirements are clearly defined to ensure compliance throughout the supply chain. **Packaging and Marking** Preservation, packaging, packing, and marking must comply with MIL-STD 2073 and the contract schedule. **Procurement Type and Set-Aside** This solicitation is a total small business set-aside, providing an opportunity for qualified small businesses to participate. Emergency Acquisition Flexibilities are invoked, and early or incremental delivery is acceptable at no additional cost to the government. **Contracting Entity and Contact Information** - Contracting Entity: NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS Mech) - Department: Department of Defense, Department of the Navy - Primary Contact: Amanda L. Bailey, Telephone: 717-605-3354, Email: [email protected] - Notice URL: [SAM.gov Opportunity](https://sam.gov/opp/93398007291c4315b90efe4f330bb94d/view) - Response Due Date: 22 June 2026 **Constant Elements Throughout Contract Lifecycle** - Strict material and quality requirements for critical shipboard application - Mandatory traceability and certification for all supplied material - Government source inspection and acceptance prior to shipment - Configuration control and change management procedures - Compliance with specified quality assurance standards - Total small business set-aside status **Special Considerations** Drawings associated with this solicitation are available on SAM.gov with restricted access; interested vendors must request access and notify the POC. Past performance will be considered in the evaluation of offers. Certification data must be submitted via Wide Area Work Flow (WAWF), and no material is to be shipped prior to acceptance. Contractors with capabilities in high-reliability, quality-assured manufacturing of nonmetallic tubing for defense applications, and robust quality management systems, are encouraged to review the full solicitation and consider submitting a response by the specified due date.