SHAFT,STRAIGHT

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

NAVSUP WEAPON SYSTEMS SUPPORT MECH

Contract Value

Not provided

Codes & Classification
Solicitation Number

N0010426QFD20

NAICS

333613 - Mechanical Power Transmission Equipment Manufacturing

Classification Code

3040

Additional Details
Set Aside

None

Place of Performance

-

SourceSAM
Documents1
The Department of the Navy, through NAVSUP Weapon Systems Support (NAVSUP WSS) Mechanicsburg, has issued a solicitation for the procurement of a SHAFT, STRAIGHT, classified under Product Service Code 3040 (Miscellaneous Power Transmission Equipment) and NAICS Code 333613 (Mechanical Power Transmission Equipment Manufacturing). This procurement is a critical requirement intended for use in a crucial shipboard system, where the integrity and reliability of the material are paramount due to the potential for catastrophic failure, serious personnel injury, or loss of vital shipboard systems if incorrect or defective material is supplied. **Purpose and Scope** The SHAFT, STRAIGHT is designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured), invoking stringent control procedures to ensure the correct material is received and installed. The item is associated with NAVSEA Drawing 7072614 and must conform to all specified requirements, with particular attention to material traceability, certification, and quality assurance. The procurement supports national defense priorities and is issued as a "DO" rated order under the Defense Priorities and Allocations System (DPAS). **Key Requirements and Deliverables** - **Material and Manufacturing:** The primary component, the Muzzle Door Operating Rod, must be manufactured in accordance with NAVSEA Drawing 7072614, using QQ-N-286, Form 2, Hot Finished, Annealed and Age Hardened material. Welding on QQ-N-286 material is strictly prohibited. - **Testing and Certification:** Quantitative chemical and mechanical analysis is required, with certifications for annealing, age hardening, and ultrasonic inspection (for starting material with a diameter or minimum distance between parallel surfaces of 4 inches or greater, or as otherwise specified). Slow strain rate tensile tests must be performed by one of several specified, approved laboratories. - **Thread Inspection:** All threads must be inspected per FED-STD-H28 series or ASME B1 series (as a commercial equivalent), with specific requirements for System 21 and System 22 as applicable. - **Traceability and Compliance:** Full traceability from material to certification test reports is mandatory. Certification data must be submitted to Portsmouth Naval Shipyard (DODAAC N50286) for review and acceptance prior to shipment, via the Wide Area Work Flow (WAWF) system. No material may be shipped before acceptance is received. - **Quality Assurance:** Contractors must maintain a quality system compliant with ISO-9001 (or MIL-I-45208 as an alternate), with calibration systems per ISO-10012 or ANSI-Z540.3 with ISO-17025. Government Quality Assurance at source is required, and the contractor’s quality system is subject to government review and audit. - **Packaging:** Preservation, packaging, packing, and marking must comply with MIL-STD-2073 and contract-specific requirements. - **Subcontractor Oversight:** The prime contractor is responsible for ensuring all sub-tier suppliers meet the same quality and traceability requirements, including periodic audits and flow-down of certification and electronic signature requirements. - **Documentation:** Certificates of compliance, test certifications, and material certification reports must be complete, accurate, and positively stated, with no disclaimers. Electronic signatures are permitted under controlled processes. **Contracting Entity and Contact Information** - **Contracting Office:** NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH) - **Department/Agency:** Department of Defense, Department of the Navy - **Primary Contact:** Alana M. Boyer, Email: [email protected], Telephone: 717-605-1234 **Procurement Type and Special Considerations** - **Solicitation Type:** This is a formal solicitation (active status) with a total small business set-aside, in accordance with applicable FAR/DFARS clauses. - **Set-Aside:** Total Small Business Set-Aside (see clause references for details). - **Evaluation:** Past performance will be considered in the evaluation of offers. - **Emergency Acquisition:** The order is issued under Emergency Acquisition Flexibilities (EAF). - **Security and Export Control:** Access to drawings may require request and approval, with distribution statements and export control considerations in accordance with OPNAVINST 5510.1 and related Navy instructions. **Schedule and Submission Requirements** - **Certification Data:** Must be submitted at least 20 days prior to scheduled delivery for review/acceptance; final delivery of material is required within 365 days after contract award. - **Delivery and Acceptance:** FOB Destination, Portsmouth Naval Shipyard (N50286). No shipment prior to acceptance. - **Wide Area Work Flow (WAWF):** All certification documentation and notifications must be processed through WAWF, with specific instructions for data entry and notification. **Constant Elements Over Contract Lifecycle** - The requirement for strict material traceability, certification, and compliance with all invoked specifications and drawings. - Maintenance of an approved quality system and government oversight at source. - Flow-down of all requirements to sub-tier suppliers and control of all subcontracted operations. - Adherence to packaging, marking, and documentation standards as specified. - Compliance with all security, export control, and distribution requirements for technical data. **Summary for Contractors** This opportunity is suited for contractors with demonstrated experience in manufacturing and certifying high-reliability, critical shipboard components under stringent quality assurance and traceability regimes. The requirement for Level I/SUBSAFE material control, comprehensive documentation, and government source inspection underscores the need for robust internal processes and supply chain oversight. Contractors must be prepared to manage detailed certification, maintain configuration control, and ensure compliance with all technical and administrative requirements throughout the contract lifecycle. Interested parties should review the full solicitation and associated technical data, request access to controlled drawings as needed, and ensure their quality systems and supply chains are capable of meeting the Navy’s exacting standards for this critical application. For further information or to request access to solicitation documents, contact Alana M. Boyer at [email protected] or 717-605-1234. Solicitation details and updates are available at: [https://sam.gov/opp/1a637a87a85b4930be99ad697477ffcf/view](https://sam.gov/opp/1a637a87a85b4930be99ad697477ffcf)