STUD,FULL BODY

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

NAVSUP WEAPON SYSTEMS SUPPORT MECH

Contract Value

Not provided

Codes & Classification
Solicitation Number

N0010426QNB93

NAICS

332722 - Bolt, Nut, Screw, Rivet, and Washer Manufacturing

Classification Code

5307

Additional Details
Set Aside

None

Place of Performance

-

SourceSAM
Documents4
The Department of the Navy, through NAVSUP Weapon Systems Support Mechanicsburg, has issued a solicitation (Procurement Identifier: N0010426QNB93) for the supply of a "STUD, FULL BODY" component. This procurement is classified under NAICS Code 332722 (Bolt, Nut, Screw, Rivet, and Washer Manufacturing) and Product Service Code 5307, indicating its focus on specialized fastener manufacturing for critical shipboard applications. **Purpose and Scope** The primary purpose of this procurement is to acquire studs for use in crucial shipboard systems. The material is designated as "SPECIAL EMPHASIS" (Level I, Scope of Certification, or Quality Assured), reflecting its criticality: incorrect or defective material could result in catastrophic failure, serious injury, loss of life, or loss of vital shipboard systems. As such, the procurement invokes stringent control procedures to ensure the correct material is received and installed. **Key Requirements and Objectives** The contract requires the manufacture and supply of studs conforming to MIL-DTL-1222, with specific configuration and material requirements: - Type: I, Style: D, Grade: B16 (ASTM-A193), Condition: Hardened and Tempered - Size: 1/2 inch diameter, Length: 2 5/16 inches - Thread Series: 13 UNC, Class of Fit: 3A (stud end), 2A (nut end) - End Configuration: Only the stud end is to be chamfered - Marking: As specified in MIL-DTL-1222, with traceability requirements - Testing: Liquid Penetrant or Magnetic Particle Inspection (Wet Method), with sampling per MIL-DTL-1222 - Complete traceability and certification for each heat/lot, including one extra fastener per lot for traceability The contract also requires compliance with a range of referenced standards, including ANSI/ASQ Z1.4, ASTM-A193, MIL-STD-792, ISO 9001, ISO 10012, ISO/IEC 17025, MIL-I-45208, MIL-STD-45662, and ANSI/NCSL Z540.3. Contractors must maintain a robust quality system, subject to government audit and verification, and provide detailed certification and test reports for all supplied material. **Quality Assurance and Deliverables** Quality assurance is paramount. The contractor must: - Maintain a quality system per ISO 9001 (or MIL-I-45208 as an alternate), with calibration per ISO 10012 or ANSI-Z540.3/ISO-17025 - Submit quality system procedures to the Procurement Contracting Officer (PCO) prior to award (unless already on file) - Allow government source inspection at the place of performance, which cannot be changed without PCO authorization - Provide certificates of compliance, traceable to each item, with detailed information as outlined in CDRL DI-MISC-80678 - Ensure all material is mercury-free - Maintain traceability from raw material to finished product, with permanent marking per MIL-STD-792 - Submit certification data to Portsmouth Naval Shipyard for review and acceptance prior to shipment, via Wide Area Work Flow (WAWF) - No material may be shipped prior to receipt of acceptance **Packaging and Handling** Preservation, packaging, packing, and marking must comply with MIL-STD 2073 and contract schedule requirements. Material handling procedures must ensure segregation, traceability, and prevention of commingling or loss of traceability throughout all processing and subcontracted operations. **Contracting Entity and Contact Information** The contracting entity is NAVSUP Weapon Systems Support Mechanicsburg, a federal office under the Department of Defense, Department of the Navy. The primary point of contact is April N. Schlussser, reachable at 771-229-0555 or [email protected]. **Procurement Type and Set-Aside** This solicitation is a fixed-price contract and is a total small business set-aside, in accordance with applicable DoD and federal regulations. Emergency Acquisition Flexibilities (EAF) apply, and the contract will be issued bilaterally, requiring written acceptance by the contractor. The contract is DPAS-rated for national defense, emergency preparedness, and energy program use. **Special Considerations** - Past performance will be considered in the evaluation of offers. - Waivers and deviations require PCO approval and must be classified as critical, major, or minor. - Engineering Change Proposals (ECPs) must be submitted for any modifications affecting form, fit, function, or interface. - Government Quality Assurance will be performed at source, and subcontractor quality assurance requirements are extensive. - All documentation and certification must be submitted electronically, and access to drawings may require request via SAM.gov and follow-up with the POC. **Constant Elements Throughout Contract Lifecycle** Throughout the contract, the requirements for quality assurance, traceability, certification, and compliance with referenced standards will remain constant. The critical nature of the material, the need for government inspection and acceptance, and the requirement for robust documentation and traceability will persist for all deliverables. **Summary for Contractors** Contractors considering this opportunity should have proven capabilities in manufacturing high-quality, traceable fasteners for critical applications, with established quality systems compliant with ISO or MIL standards. Experience with government contracts, source inspection, and electronic certification submission is essential. The contract is suitable for small businesses specializing in bolt, nut, screw, rivet, and washer manufacturing, particularly those familiar with Navy and DoD requirements for Level I/SUBSAFE material. For further details and to access solicitation documents, contractors should visit the official notice at [SAM.gov](https://sam.gov/opp/6d51ea049d194bbe839256d75dddaba7/view).