TUBING,NONMETALLIC
Key Dates
Due Date
-
Posted Date
-
Agency & Value
Agency
NAVSUP WEAPON SYSTEMS SUPPORT MECH
Contract Value
Not provided
Codes & Classification
Solicitation Number
N0010426QFC25
NAICS
326220 - Rubber and Plastics Hoses and Belting Manufacturing
Classification Code
4720
Additional Details
Documents1
The Department of the Navy, through NAVSUP Weapon Systems Support (Mechanicsburg), has issued a solicitation for the procurement of nonmetallic tubing, specifically MC 903 Nylon Tube for Ball Valve Seat/Seal material, under solicitation number N0010426QFC25. This procurement is classified under NAICS code 326220 (Rubber and Plastics Hoses and Belting Manufacturing) and Product Service Code 4720, indicating its relevance to contractors specializing in the manufacture of rubber and plastic hoses, belting, and related products.
**Purpose and Scope**
The tubing to be supplied is intended for use in a critical shipboard system, where material integrity is paramount. The contract designates the tubing as "SPECIAL EMPHASIS material" (Level I, Scope of Certification, or Quality Assured), reflecting the high probability of catastrophic failure should incorrect or defective material be used. Such failure could result in serious personnel injury, loss of life, or loss of vital shipboard systems, including the ship itself. Accordingly, stringent control procedures and quality assurance requirements are invoked to ensure the correct material is received and installed.
**Key Requirements and Objectives**
The MC 903 Nylon Tube must conform to Electric Boat Division Specification 2000, with specific dimensional and material properties:
- Outside Diameter: 15.470 inches
- Inside Diameter: 10.200 inches
- Length: 10 inches
- Tolerances: As per Paragraph 3.3.2 of E.B. SPEC 2000
Material properties must meet or exceed the following standards:
- Melting Point: 221°C ± 9 (ASTM E794 or D3418)
- Relative Viscosity: Minimum 2000 (ASTM D789)
- Specific Gravity: 1.15–1.17 at 23°C (ASTM D792)
- Dimensional Change: Maximum 0.2%
- Tensile Impact: Minimum 80 ft-lbs/in² (ASTM D1822 Type S)
- Tensile Yield Stress: Minimum 9000 psi (ASTM D638)
- Compressive Strength: Minimum 9000 psi (ASTM D695)
- Water Absorption: Maximum 1.3% (24hr), 7.0% (saturation) (ASTM D570)
- Rockwell "M" Hardness: Minimum 75 (ASTM D785)
The material must be MC903 (Type 6 cast nylon produced with polyepsilon caprolactam by direct polymerization), manufactured by Polymer Corporation or equivalent, and certified to Electric Boat Division Specification 2000.
**Certification, Traceability, and Quality Assurance**
Contractors must provide a Certificate of Compliance for all items, certifying adherence to all requirements, specifications, and drawings. Traceability is critical: each tube must be permanently marked (except Teflon seats, which are tagged) with a unique traceability number, heat-lot, or batch number, directly linking the material to its certification data. Certification test reports must accompany each batch, detailing specification, class, form, grade, type, process, and composition.
Quality system requirements are rigorous, mandating compliance with ISO-9001, ISO-10012, ANSI/NCSL Z540.3, and ISO/IEC 17025, or MIL-I-45208. The contractor’s quality system and products are subject to government evaluation, verification, inspection, and acceptance. Suppliers of Level I/SUBSAFE material must submit documented quality system procedures to the Procurement Contracting Officer (PCO) prior to award, unless already on file.
Government Quality Assurance will be performed at the source, and any changes to the place of performance require PCO authorization. Subcontractor inspection requirements are also detailed, with the prime contractor responsible for ensuring compliance and maintaining traceability throughout the supply chain.
**Packaging and Delivery**
Preservation, packaging, packing, and marking must comply with MIL-STD 2073 and contract schedule requirements. Certification data must be submitted to Portsmouth Naval Shipyard for review and acceptance prior to each shipment, via Wide Area Work Flow (WAWF). No material may be shipped before acceptance is received.
The proposed delivery schedule requires submission of all certification data (CDRLs) 20 days prior to delivery, with final delivery of material within 365 days. Early and incremental deliveries are acceptable at no additional cost to the government.
**Contracting Entity and Contact Information**
- Contracting Entity: NAVSUP Weapon Systems Support (Mechanicsburg)
- Department: Department of Defense, Department of the Navy
- Primary Contact: Amanda L. Bailey, Telephone: 717-605-3354, Email: [email protected]
- Notice URL: [SAM.gov Opportunity](https://sam.gov/opp/ae1afee019ce452b8d21aa259781a74b/view)
**Procurement Type and Special Considerations**
This is a fixed-price supply contract issued under Emergency Acquisition Flexibilities. The procurement was initially set aside for small business, but the set-aside has since been dissolved. The contract invokes Buy American and Free Trade Agreements provisions, and compliance with balance of payments program requirements is required. Past performance will be considered in the evaluation of offers.
**Constant Elements Throughout Contract Lifecycle**
- Strict adherence to material specifications and certification requirements
- Maintenance of traceability and quality assurance documentation
- Compliance with government inspection and acceptance procedures
- Preservation, packaging, and marking per military standards
- Submission of certification data prior to shipment and acceptance
- Permanent marking and traceability for all supplied materials
**Summary for Contractors**
This opportunity is suited for manufacturers with proven capabilities in producing high-quality, certified nonmetallic tubing for critical defense applications, particularly those with robust quality management systems and experience in traceability and compliance with military specifications. The contract demands meticulous attention to material properties, certification, and quality assurance, with government oversight at every stage. Contractors must be prepared to manage complex documentation, traceability, and inspection requirements, and to coordinate closely with NAVSUP and Portsmouth Naval Shipyard for certification and acceptance.
Interested parties should review the full solicitation and technical requirements, and direct any questions to the primary contact listed above. The solicitation remains active, with responses due by April 5, 2026.