PIPE, SEAMLESS
Key Dates
Due Date
-
Posted Date
-
Agency & Value
Agency
NAVSUP WEAPON SYSTEMS SUPPORT MECH
Contract Value
Not provided
Codes & Classification
Solicitation Number
N0010426QNB44
NAICS
331420 - Copper Rolling, Drawing, Extruding, and Alloying
Classification Code
4710
Additional Details
The Department of the Navy, through NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH), has issued a solicitation for the supply of seamless pipe, designated as a critical safety item for shipboard systems. This procurement, identified by solicitation number N0010426QNB44, is classified under NAICS code 331420 (Copper Rolling, Drawing, Extruding, and Alloying) and Product Service Code 4710 (Pipe, Tube, and Rigid Tubing). The opportunity is posted on SAM.gov and remains active, with responses due by April 16, 2026.
**Purpose and Scope**
The seamless pipe to be procured will be used in vital shipboard systems where material integrity is paramount. The failure or malfunction of this material could result in catastrophic outcomes, including serious injury, loss of life, or loss of critical shipboard functions. As such, the pipe is designated as "SPECIAL EMPHASIS" material (Level I, Scope of Certification, or Quality Assured), invoking rigorous control procedures to ensure the correct material is received and installed.
**Key Requirements and Objectives**
The solicitation specifies that the pipe must conform to MIL-P-24691/1, Grade B, with a nominal size of 1 inch and Schedule 80. Unless otherwise specified, pipes should be supplied in single random lengths of 15 to 22 feet, with permissible variations for a small percentage of shorter (12–15 feet) and longer (22–24 feet) pieces. The material must be seamless, and ultrasonic inspection—including shear wave testing in two circumferential directions—is required. Hydrostatic testing is mandatory; eddy current testing is not an acceptable substitute.
Surface finish requirements are strict: the finished material must be clean, free of varnish, dirt, loose scale, paint, or other foreign matter, and must not exceed 250 Ra (micro inches) with no waviness. Varnish as a preservative is prohibited. Special marking and traceability requirements are invoked, including both permanent and temporary markings per MIL-STD-792 and other referenced standards.
**Quality Assurance and Certification**
The contractor must maintain a quality system compliant with ISO-9001 (or MIL-I-45208 as an alternate), with calibration systems per ISO-10012, ANSI-Z540.3, and ISO-17025. The quality system and all products are subject to government evaluation, verification, and audit. Certification of chemical and mechanical properties must be provided in accordance with DI-MISC-81020, and a certificate of compliance is required for all items, demonstrating full adherence to specifications and traceability to material markings.
All inspection and test records must be maintained and traceable to the material inspected. Subcontractor quality assurance is also emphasized, requiring periodic reviews and audits to ensure continued compliance. The government reserves the right to inspect supplies at source and destination.
**Packaging and Handling**
Preservation, packaging, packing, and marking must comply with MIL-STD-2073 and other contract requirements. Material handling procedures must ensure traceability and prevent commingling of heats/lots, especially during subcontracted operations.
**Contracting Entity and Contact Information**
The contracting entity is NAVSUP Weapon Systems Support Mechanicsburg, a federal office under the Department of Defense, Department of the Navy. The primary point of contact is Jocelyne Dzonangfouego, reachable at 717-605-2982 or via email at [email protected].
**Procurement Type and Set-Aside**
This solicitation is a total small business set-aside, as indicated by the inclusion of the relevant FAR clause. Emergency Acquisition Flexibilities (EAF) are invoked, and the resultant contract will be issued bilaterally, requiring written acceptance by the contractor. The contract is certified for national defense under the Defense Priorities and Allocations System (DPAS), with a priority rating of "DO."
**Special Considerations**
- Certification data must be submitted to Portsmouth Naval Shipyard for review and acceptance prior to each shipment, via Wide Area Work Flow (WAWF).
- No material may be shipped before receipt of government acceptance.
- Mercury and mercury-containing compounds are strictly prohibited.
- Configuration control, including submission of Engineering Change Proposals (ECPs) for any modifications, is required.
- Waivers and deviations must be submitted and approved by the contracting officer, classified as critical, major, or minor.
- The solicitation references numerous standards and specifications, including ANSI/ASQ Z1.4, ASTM-A530, ASTM-B666, MIL-STD-792, SAE AMS 2806/2807/2809, ISO 9001/10012/17025, and others.
**Constant Elements Throughout Contract Lifecycle**
The critical safety designation, traceability and certification requirements, quality assurance standards, packaging and marking protocols, and configuration control procedures will remain in force throughout the contract lifecycle. The government’s right to inspect, audit, and require compliance with all specified standards is a constant feature.
**Summary for Contractors**
Contractors considering this opportunity must have robust quality assurance systems, experience with high-integrity shipboard materials, and the ability to meet stringent traceability, certification, and inspection requirements. The solicitation is highly technical and demands strict adherence to military and industry standards. Only small businesses are eligible, and the contract supports national defense priorities. Interested parties should review the full solicitation on SAM.gov and direct any questions to the primary contact listed above.
For further details and to access the solicitation, visit: [SAM.gov Opportunity](https://sam.gov/opp/b6c6373a759041cc9dba3a0e46581b99/view).