SLIDE

Key Dates
Due Date

-

Posted Date

-

Agency & Value
Agency

NAVSUP WEAPON SYSTEMS SUPPORT MECH

Contract Value

Not provided

Codes & Classification
Solicitation Number

N0010426QFB20

NAICS

332919 - Other Metal Valve and Pipe Fitting Manufacturing

Classification Code

4820

Additional Details
Set Aside

None

Place of Performance

-

SourceSAM
The Department of the Navy, through NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH), has issued a solicitation (Procurement Identifier: N0010426QFB20) for the supply of a "Slide" component, classified under NAICS code 332919 (Other Metal Valve and Pipe Fitting Manufacturing) and Product Service Code 4820. This procurement is a total small business set-aside, inviting qualified small business contractors to participate. **Purpose and Scope** The material solicited under this contract is intended for use in a critical shipboard system. Due to the essential nature of its application, any incorrect or defective material could result in catastrophic failure, including serious personnel injury, loss of life, or loss of vital shipboard systems. As such, the item is designated as SPECIAL EMPHASIS material (Level I, Scope of Certification, or Quality Assured), requiring rigorous control procedures to ensure the correct material is received and installed. **Key Requirements and Objectives** The primary deliverable is a "Slide" manufactured in strict accordance with Naval Sea Systems Command Drawing 751-6402630, Find Number 1, and DN6402630B1, subject to any amplifications or modifications specified in the solicitation. The material must be QQ-N-286, Form 2, Annealed (hot finished or cold drawn) and Age Hardened, Finish A/B. Weld repair is explicitly prohibited on QQ-N-286 material. Certifications are required for quantitative chemical and mechanical analysis, as well as for ultrasonic inspection on starting material with a diameter or minimum distance between parallel surfaces of 4 inches or greater, or as otherwise specified. The Slow Strain Rate Tensile Test for QQ-N-286 must be performed by one of several designated laboratories, including Huntington Alloys, Metallurgical Consultants, Naval Surface Warfare Center Carderock Division, Teledyne Allvac, Westmoreland Mechanical Testing and Research, Mannesmann Rohrenwerke, and ThyssenKrupp VDM USA. Thread inspection must comply with FED-STD-H28 series, with System 21 as the minimum requirement unless otherwise specified. All internal threads must be formed by cutting; cold forming is not acceptable. Contractors must submit a Certificate of Compliance certifying that all items furnished meet the requirements of the procurement document, including all invoked specifications and drawings. Configuration control is required, with any waivers or deviations subject to review and approval by the Contracting Officer. Engineering Change Proposals (ECPs) must be submitted for any modifications affecting form, fit, function, or interface parameters. Mercury and mercury-containing compounds are strictly prohibited from being intentionally added or coming into contact with supplied hardware. **Quality Assurance and Traceability** A robust quality system is mandatory, conforming to ISO-9001 (with calibration system requirements per ISO-10012 or ANSI-Z540.3 with ISO-17025), or MIL-I-45208 with calibration per MIL-STD-45662. The quality system and products are subject to evaluation, verification, inspection, and acceptance by government representatives. Suppliers of Level I/SUBSAFE material must submit documented quality system procedures to the Procurement Contracting Officer prior to award, unless already on file. Inspection records must be maintained and traceable to the material inspected. Subcontractor inspection requirements are detailed, including government rights to inspect at source and requirements for supplier quality assurance programs. Traceability and certification requirements are stringent, with material certification reports required to reflect full compliance with specified requirements. Traceability must be maintained from material to certification test report and other Objective Quality Evidence (OQE). Material marking for traceability and identification must be permanent and conform to MIL-STD-792, with alternate methods permissible only if specified. Receiving inspection must verify traceability markings, certification test report completeness, and compliance with specifications. Nonconforming products must be controlled and reported, with records available for government review. Final inspection includes material sampling for form, fit, and function, with lot acceptance based on zero defects. All data concerning material verification, traceability, and nondestructive test certifications must be 100% inspected. **Packaging and Delivery** Preservation, packaging, packing, and marking must comply with MIL-STD 2073 and the contract schedule. Certification data must be submitted to Portsmouth Naval Shipyard for review and acceptance prior to each shipment, via Wide Area Work Flow (WAWF). No material may be shipped prior to receipt of acceptance. **Contracting Entity and Contact Information** - Contracting Entity: NAVSUP Weapon Systems Support Mechanicsburg (NAVSUP WSS MECH) - Department: Department of Defense, Department of the Navy - Primary Contact: Scott R. Youngblood, Telephone: 717-605-2379, Email: [email protected] - Notice URL: [SAM.gov Opportunity](https://sam.gov/opp/5afaa7630eac496fa61a143f95210dc5/view) **Procurement Type and Special Considerations** This is a fixed-price solicitation, DO rated for national defense use under the Defense Priorities and Allocations System (DPAS). The procurement is a total small business set-aside, and past performance will be considered in the evaluation of offers. The Buy American and Free Trade Agreements provisions apply. **Constant Elements Over Contract Lifecycle** Throughout the contract lifecycle, the requirements for material quality, traceability, certification, configuration control, and compliance with specified standards and drawings will remain constant. The rigorous quality assurance and inspection protocols, as well as the prohibition of mercury and weld repair, are enduring requirements. The use of designated laboratories for specific tests and the submission of certification data prior to shipment are also persistent obligations. **Summary for Contractors** Contractors considering this opportunity should ensure they have the capability to manufacture and certify a highly specialized metal component for critical shipboard systems, with robust quality assurance, traceability, and compliance systems in place. The solicitation demands strict adherence to Navy specifications, comprehensive documentation, and the ability to interface with government quality assurance and inspection processes. Only small businesses are eligible, and the contract is subject to national defense priorities. Interested parties should review the solicitation in detail and direct any questions to the primary contact listed above.